VLAN

CONFIGURACION FRAME RELAY PUNTO A PUNTO

Router(config)#int s0/0/0
Router(config-if)#no sh
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

Router(config-if)#no kee
Router(config-if)#no keepalive
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

Router(config-if)#enc
Router(config-if)#encapsulation fr
Router(config-if)#encapsulation frame-relay e
Router(config-if)#encapsulation frame-relay i
Router(config-if)#encapsulation frame-relay ietf (Debemos especificar la encapsulacion del Router que sea igual para todas en este caso IETF, ya que si no se les configura este los trae por defecto en cisco) 
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

Router(config-if)#clock
Router(config-if)#clock r
Router(config-if)#clock rate 1000000
Router(config-if)#exit
Router(config)#int s0/0/0.17 p
Router(config)#int s0/0/0.17 point-to-point
Router(config-subif)#
%LINK-5-CHANGED: Interface Serial0/0/0.17, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0.17, changed state to up

Router(config-subif)#description 17
Router(config-subif)#bandwidth 500
Router(config-subif)#frame-relay in
Router(config-subif)#frame-relay interface-dlci 17
Router(config-subif)#ip add 192.168.10.2 255.255.255.0
Router(config-subif)#exit
Router(config)#


Router(config)#int s0/0/0.18 p
Router(config)#int s0/0/0.18 point-to-point
Router(config-subif)#
%LINK-5-CHANGED: Interface Serial0/0/0.18, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0.18, changed state to up

Router(config-subif)#des
Router(config-subif)#description 18
Router(config-subif)#ban
Router(config-subif)#bandwidth 500
Router(config-subif)#ip add 192.168.30.3 255.255.255.0 (Se le configura esta IP porque debe estar en la misma red que el router con el cual esta enlazado y teniendo en cuenta que deben de ir en diferentes DLCS)
Router(config-subif)#frame-relay interface-dlci 18

NOTA: Aplicar la misma configuracion a cada uno de los routers teniendo encuenta que cada router debe de tener un DLCI distinto.

Router(config)#int s0/0/0.19 p
Router(config)#int s0/0/0.19 point-to-point
Router(config-subif)#
%LINK-5-CHANGED: Interface Serial0/0/0.19, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0.19, changed state to up

Router(config-subif)#description 19
Router(config-subif)#bandwidth 500
Router(config-subif)#ip add 192.168.10.3 255.255.255.0 ( Esta Ip esta en el mismo rango de red que el DLCI 17)
Router(config-subif)#frame-relay in
Router(config-subif)#frame-relay interface-dlci 19
Router(config-subif)#exit
Router(config)#int s0/0/0.20 point-to-point
Router(config-subif)#
%LINK-5-CHANGED: Interface Serial0/0/0.20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0.20, changed state to up

Router(config-subif)#description 20
Router(config-subif)#bandwidth 500
Router(config-subif)#ip add 192.168.20.2 255.255.255.0
Router(config-subif)#frame-relay in
Router(config-subif)#frame-relay interface-dlci 20
Router(config-subif)#exit
Router(config)#






CONFIGURACION DE LA NUBE

Se introducen los siguiente comandos para el emparejamiento de los DLCI:

Router(config)#int s0/0/0
Router(config-if)# frame relay route 17 int s0/0/0 19
Router(config-if)#no shutdown

Router(config)#int s0/0/0
Router(config-if)# frame relay route 20 int s0/0/1 21
Router(config-if)#no shutdown

Router(config)#int s0/0/0
Router(config-if)# frame relay route 22 int s0/0/2 18
Router(config-if)#no shutdown




CONVERTIR ROUTER A SWITCH FRAME RELAY

Router(Config)#frame-relay-switching